Replacing the Propane Regulator in Agile

This article is not intended to qualify anyone to work on a propane system. Propane when improperly handled can be very dangerous and should always be treated with the utmost respect. If there is ever a concern about a propane system, a qualified technician should check it out as soon as possible.

The propane regulator is the heart of the propane system, if it fails, appliances that uses propane as fuel will no longer work and that can be a major headache for anyone dry camping. Leaking at the propane regulator is one of the major regulator failures. If you noticed a propane leak in the system, it is highly advised to shut the propane flow at the service valve to prevent further leaking that can/ may result in disastrous situations.

Agile has a two-stage horizontal mount propane regulator and a single high pressure regulator feeding the outdoor pig tail that is located on the passenger side rear wheel well area. The propane regulator is mounted on the propane tank towards the rear end and can only be accessed under the RV.

I highly recommend that a qualified propane technician do the propane regulator replacement. If you are out camping and needed to change the propane regulator, you are doing so at your own risk. This article is only intended to familiarize you with the propane regulator in RT Agile and not intended to qualify anyone to work on propane system.

Before you start, make sure to close the propane service valve.

1. Disconnect the propane pigtail hose from the propane service port. The thread on the pigtail (P.O.L end) is reversed as marked with the indentation on the P.O.L nut; turn clockwise to loosen from the service valve outlet port.

Samuel P. Taylor State Park, Lagunitas California

Samuel P. Taylor State Park Campground is a short drive from Bay area. The campground is located within the state park and in close proximity to Muir Woods National Monument and Point Reyes National Seashore.

GPS Coordinates (Entrance Kiosk): 38.019266,-122.729944
Samuel P. Taylor SP website: Click here
Campground Map (Pdf): Click here
Campground reviews (RVparkreviews): Click here

Video tour of Samuel P. Taylor Campground (HD available).

Sandy Riverfront RV Resort, Troutdale Oregon

Sandy Riverfront RV resort is located close to the Columbia River Gorge  and about 20 minutes east of downtown Portland. It is a good camp base to visit the waterfalls, the Columbia river, and all the surrounding cities.

GPS Coordinates (CG Entrance): 45.5383,-122.379096
Campground Website: Click here
Campground Map: Click here
Campground reviews from RVParkreviews: Click here

 

Video tour of Sandy Riverfront RV Resort Campground (HD available).

Permanent Black Holding Tank Rinser

If you’re tired of hauling the garden hose inside the RV to flush and clean the black holding tank, installing a permanent holding tank rinser may interest you. There are 3 permanent holding tank flusher/rinser device on the market that I know; one is the “Tornado Rotary Tank Rinser”, the “No-Fuss Flush” unit and the identical “Camco Quickie Flush” system. I went and bought the “No-Fuss Flush” unit as it was available at my local RV store. The “No-Fush Flush” unit does not come with an extension hose unlike the “Quickie Flush” seen on Amazon here: Click here. All of the above mentioned tank flush unit has a built in check valve to prevent any contents of the holding tank exiting via the flushing unit. The supplied holding screws (x3 zinc coated) for the "No-Fuss Flush" unit were not used, instead I purchased 3 stainless steel screws for this project.

1. Before starting with this project, make sure your black holding tank is empty; you do not want any surprises when drilling the required hole.

2. Raise the passenger side wheels on ramps for easy access to underside of the RV. For safety, chock the driver side wheels to prevent the RV from rolling off the ramps.

3. The installation location of the tank flushing unit is limited on the Agile as the only exposed side of the black tank is towards the rear end of the vehicle; all other sides are either covered by a shield or frame. Although, installing the flushing unit at this location is ideal as it can spray at the area where most solid waste might accumulate. The flushing unit does not spray directly at the tank sensors and at the area where the tank drains due to the tank design, although it might indirectly. The uppermost portion of black tank is partially covered by a frame, the most I can install it is about 3 inches from the top of the tank an inch shy of the flushing unit requirement of 2 inches.

4. Make sure you are 100% positive where to make the hole, this is a one-shot attempt and cannot be reverted. “No-Fuss Flush” device requires an inch diameter hole. A hole saw is ideal for making the hole because it captures the cut remnant, preventing it from falling into the tank.

Replacing the Macerator Impeller

A replacement impeller kit for SHURflo macerator pump is available on Amazon: SHURflo 9457100 Macerator Impeller Kit

Optional:

• The original macerator discharge hose is a 1-inch ID Kanaflex hose. You can get on EBay by the foot, just click on the link.
• Macerator pump replacement: Shurflo Macerator

Step-by-step procedures:

Before starting, make sure that the house battery is off or disconnected. Clean and empty both holding tanks. Some waste fluid is expected to drip when you start disconnecting the macerator inlet and outlet ports, so be prepared. I used a small bucket to catch all the remaining waste fluids in the line.

1. Raise the passenger wheels on ramps for easy access to underside of the RV. I made wooden ramps for this purpose. For safety, chock the driver side wheels to prevent the RV from rolling off the ramps.